Skip to content
Hydronics

Pump Cavitation and NPSH: Check the Hydronic Inlet Pressure

A pump can meet its flow and head duty yet have an unsuitable inlet condition. Separate circulation head from absolute suction pressure, temperature and the manufacturer’s NPSH requirement.

Published by MEPFlow · Methods and limitations · Primary references

November 12, 2026 13 min read Updated November 12, 2026

Connect the hydronic duty to the supplier review

Use MEPFlow for hydronic layouts and circuit sizing. Check the separate inlet-pressure budget with the worksheets below and the pump supplier’s selection data.

Explore hydronic design
In this guide: jump to a step

A pump schedule normally lists flow and head. A reliable selection also needs an inlet-pressure check. Hot water can have less pressure available above its boiling threshold than a cold gauge reading suggests, and a closed loop is not automatically protected from cavitation.

Follow one original water-system example from gauge pressure to available NPSH, then change temperature and inlet pressure separately. The goal is to prepare a clear selection brief, not to choose a universal fill pressure or NPSH allowance.

For the complete layout, explore MEPFlow’s hydronic design and pipe sizing software and review equipment duty, water flow, pipe sizes and circuit assumptions together.

1. Separate circulation head from suction pressure

A pump can meet the scheduled flow and head while having an unsuitable inlet condition. Its duty head is the energy added between suction and discharge. Net positive suction head available, or NPSHA, describes how much total head the liquid has above its vapor-pressure head at the pump inlet datum. These are different checks.

Inside a centrifugal pump, pressure falls as liquid approaches the impeller before the pump raises it. If local pressure falls far enough, vapor cavities can form and then collapse in a higher-pressure region. Noise, vibration and declining performance deserve investigation, but noise alone cannot identify the cause: entrained air, a restriction or mechanical damage can produce similar symptoms.

Use the critical-circuit pump-head calculation to establish circulation duty. Then assess suction conditions separately. Building height is not added to closed-loop friction head, but elevation still changes local static pressure and therefore matters to this second calculation.

Three pressure questions that need different evidence
QuestionRelevant quantityEvidence to retain
Can the pump circulate the design flow?Differential duty headComplete circuit losses and selected pump curve
What inlet condition does the system provide?NPSHAOperating inlet pressure, datum, temperature and fluid properties
What inlet condition does this pump need?Manufacturer NPSHR plus applicable marginExact pump, speed, flow range and selection requirements

2. Use absolute pressure and one defined datum

A normal gauge reads pressure relative to the surrounding atmosphere. Vapor-pressure data use absolute pressure. Add the local atmospheric pressure to a gauge reading before comparing them. Using a sea-level assumption at an elevated site overstates the available pressure; use the project location and operating pressure basis.

The following expression applies to a static-pressure reading at the pump suction flange, at the same elevation as the manufacturer’s NPSH datum, with the associated inlet velocity. The velocity term converts static pressure head to total suction head. Use pascals, kilograms per cubic metre and metres per second throughout.

If the pressure tap is elsewhere, first translate its total head to the required datum: account for elevation, changes in velocity and losses between the tap and the inlet. Label both points on the calculation. Do not simply paste a boiler-room gauge reading into the flange equation.

A running flange reading already reflects the upstream pipe, valve and strainer losses for that condition. Subtracting those same losses again double-counts them. Conversely, a calculation starting at a remote reference point must include the route to the pump. A stopped-pump fill reading cannot replace an operating suction reading.

NPSHA = (p_atm + p_g − p_v) ÷ (ρg) + v² ÷ (2g)

p_atm: local atmospheric pressure, absolute; p_g: operating suction static gauge pressure; p_v: liquid vapor pressure, absolute. All pressures are Pa. ρ is liquid density in kg/m³, g = 9.80665 m/s², and v is inlet velocity in m/s. Result: metres of the pumped liquid. This form assumes the suction tap and manufacturer datum are at the same elevation.

Connect the hydronic duty to the supplier review

Use MEPFlow for hydronic layouts and circuit sizing. Check the separate inlet-pressure budget with the worksheets below and the pump supplier’s selection data.

Start free trial

3. Work an inlet-pressure example from the actual pipe bore

Consider an illustrative horizontal water pump operating at 3.0 L/s through a 50 mm actual-inside-diameter suction connection. The local atmospheric pressure is 98 kPa absolute, the running suction static reading is 40 kPa gauge, and water temperature is 80°C. The pressure tap and manufacturer datum are at the same elevation. These are teaching inputs, not recommended fill settings.

The inlet area is π × 0.050² / 4 = 0.0019635 m². Dividing 0.003 m³/s by this area gives 1.528 m/s. Its velocity head is 1.528² / (2 × 9.80665) = 0.119 m. Nominal connection size is not a substitute for the actual flow area.

The Hydraulic Institute water table gives a saturation density of 971.77 kg/m³ and absolute vapor pressure of 0.047414 MPa at 80°C. For this low-pressure water illustration, use that density as an approximation and convert vapor pressure to 47,414 Pa. For precise equipment selection, obtain properties at the specified fluid composition and operating state.

The absolute inlet static pressure is (98 + 40) × 1,000 = 138,000 Pa. After subtracting the vapor-pressure contribution and adding velocity head, NPSHA is 9.625 m, rounded to 9.62 m. Keep unrounded values until the final result. This number describes the system’s inlet condition; acceptance still needs the selected pump’s requirement.

From a gauge reading to available suction head

Original head budget for pure water at 80°C. The inlet pressure reading is at the pump datum. Scroll horizontally on small screens; the arithmetic is repeated below.

Available NPSH is the total absolute inlet head less the water vapor-pressure headThe local atmospheric pressure is 98 kilopascals absolute. A running inlet gauge reading of 40 kilopascals gives 138 kilopascals absolute at the pump datum. At 80 degrees Celsius, water density is 971.77 kilograms per cubic metre and vapor pressure is 47.414 kilopascals absolute. The pressure head is 14.480879 metres. A flow of 3 litres per second in an actual 50 millimetre bore gives velocity 1.527887 metres per second and velocity head 0.119023 metres. Total inlet head is 14.599902 metres. Subtracting vapor-pressure head 4.975336 metres leaves available NPSH 9.624566 metres, rounded to 9.62 metres. Both horizontal bars begin at zero and use the same scale. Compare the result with the selected pump manufacturer’s NPSHR and application-specific margin separately.RUNNING INLET PRESSURE AT THE PUMP DATUM98 kPa absolute + 40 kPa gauge = 138 kPa absoluteTwo views of the same total inlet head: 14.5999 m0481216Inlet total headAbsolute pressure head: 14.4809 mVelocity head: +0.1190 mHead allocationVapor head: 4.9753 mAvailable NPSH: 9.6246 mHead of the pumped water (m), starting at zero14.4809 + 0.1190 − 4.9753 = 9.6246 mNext: compare with the selected pump’s NPSHR and required margin at this duty.
Absolute inlet pressure head
138,000 ÷ (971.77 × 9.80665) = 14.4809 m
Velocity head
1.527887² ÷ (2 × 9.80665) = 0.1190 m
Water vapor-pressure head
47,414 ÷ (971.77 × 9.80665) = 4.9753 m

Both bars use the same length scale. Pressure is static at the inlet flange, at the manufacturer’s reference elevation, so velocity head is added once and no elevation correction is used in this example. Head is metres of water at 80°C, not metres based on a fixed cold-water density. Available NPSH alone does not establish an acceptable pump selection.

Original 80°C example: the inlet head budget
TermCalculation or inputHead contribution
Absolute inlet static head138,000 ÷ (971.77 × 9.80665)+14.481 m
Vapor-pressure head47,414 ÷ (971.77 × 9.80665)−4.975 m
Inlet velocity head1.527887² ÷ (2 × 9.80665)+0.119 m
NPSHA14.480879 − 4.975336 + 0.1190239.625 m → 9.62 m

4. Ask what the manufacturer’s NPSH curve represents

NPSHR is supplied by the pump manufacturer for the relevant flow, speed and liquid. NPSH3 is a test quantity associated with a 3% reduction in head due to cavitation. Do not label every published NPSHR curve as NPSH3 or treat a point on either curve as a guarantee of bubble-free operation.

The Hydraulic Institute’s public explanation of ANSI/HI 9.6.1-2024 distinguishes manufacturer-published NPSHR from NPSH3; the published requirement may be higher. The margin is application-dependent. Obtain the applicable manufacturer and project requirements rather than applying a universal extra metre or percentage.

For a transparent arithmetic demonstration only, suppose an equipment review specifies NPSHR = 4.0 m and an additional margin of 1.5 m at this operating point. The example target becomes 5.5 m. The calculated 9.62 m exceeds that assumed target by 4.12 m. These invented selection inputs do not represent a real model, a standard’s required margin or approval of a pump.

Check the full permitted operating range, not just the design point. Maximum flow, alternate speeds and parallel-pump modes can change both the system’s available head and the pump’s requirement. A speed change should be assessed with the appropriate manufacturer data; do not scale an NPSHR curve using the ordinary head affinity rule.

5. Test temperature and pressure sensitivity separately

Water’s vapor pressure rises sharply with temperature. To see that effect clearly, hold the example’s atmospheric pressure, gauge pressure, flow and pipe bore fixed, then update density and vapor pressure. At 60°C the calculated NPSHA is 12.36 m; at 80°C it is 9.62 m; at 90°C it is 7.28 m.

This is a sensitivity comparison, not a prediction that pressure remains constant while a closed system heats. The expansion tank and pressurization arrangement influence actual operating pressure. Use measured or calculated coincident pressure and temperature conditions for the real installation.

Now retain 90°C water but reduce the running suction gauge pressure from 40 to 10 kPa. NPSHA falls to 4.11 m. It would miss the illustrative 5.5 m target by 1.39 m. The same pump can therefore have a different assessment when its inlet condition changes, even before its flow or speed changes.

Keep these calculations in the review record rather than judging the system from a single cold commissioning reading. The water-property values below are for water only. A glycol mixture needs its own density, vapor-pressure information and manufacturer selection guidance; see the glycol design guide.

Warmer water uses more of the suction-pressure budget

Original temperature sensitivity at the same assumed inlet gauge pressure, local atmosphere, flow and bore. Scroll horizontally on small screens; exact inputs and results are listed below.

Available NPSH falls from 12.36 to 7.28 metres as water temperature rises from 60 to 90 degrees Celsius in this fixed-pressure sensitivityThree bars share a zero-based head scale in metres. With an assumed running gauge pressure of 40 kilopascals, local atmospheric pressure of 98 kilopascals absolute, flow of 3 litres per second and actual inlet bore of 50 millimetres, calculated available NPSH is 12.36 metres at 60 degrees Celsius, 9.62 metres at 80 degrees Celsius, and 7.28 metres at 90 degrees Celsius. Water vapor pressures are respectively 19.946, 47.414 and 70.182 kilopascals absolute; density is changed for each temperature. This sensitivity holds inlet gauge pressure fixed to isolate temperature, not to predict how the pressure in a real closed loop changes as it heats. A separate 90-degree case at 10 kilopascals gauge has 4.11 metres of available NPSH. No pump requirement or universal margin is plotted.Temperature changes vapor pressure and water densityFixed sensitivity inputs: 40 kPa gauge + 98 kPa atmosphere; 3.0 L/s; 50 mm bore02468101214Available NPSH (m)12.36 m60°CVapor: 19.946 kPa abs.9.62 m80°CVapor: 47.414 kPa abs.7.28 m90°CVapor: 70.182 kPa abs.Separate stress case: 90°C and only 10 kPa gauge → 4.11 m NPSHAActual loop pressure can change with temperature, pressurization and pump operation.
Water at 60°C
Vapor pressure 19.946 kPa absolute; available NPSH 12.36 m.
Water at 80°C
Vapor pressure 47.414 kPa absolute; available NPSH 9.62 m.
Water at 90°C
Vapor pressure 70.182 kPa absolute; available NPSH 7.28 m.

This is a sensitivity comparison, not a prediction of a sealed system heating up at constant gauge pressure. Density is 983.16, 971.77 and 965.3 kg/m³ at 60, 80 and 90°C respectively. The pump’s NPSHR and the required margin must be checked separately. Use fluid-specific properties for glycol mixtures.

Original sensitivity study: 98 kPa atmosphere, 3 L/s, 50 mm bore and identical datum
Water temperatureDensity / vapor pressureSuction gauge pressureCalculated NPSHA
60°C983.16 kg/m³ / 19.946 kPa absolute40 kPa12.36 m
80°C971.77 kg/m³ / 47.414 kPa absolute40 kPa9.62 m
90°C965.30 kg/m³ / 70.182 kPa absolute40 kPa7.28 m
90°C, reduced inlet pressure965.30 kg/m³ / 70.182 kPa absolute10 kPa4.11 m

6. Locate the pressure reference before changing the pump

In a closed hydronic loop, the expansion-tank connection anchors the pressure distribution for a given thermal condition. Caleffi’s circulation guidance explains why placing that connection close to the circulator inlet helps avoid a large operating suction-pressure reduction. The location of the connection matters, not just the physical location of the tank.

That point is not fixed at one pressure through every heating and cooling cycle. Tank acceptance, precharge, fill arrangement and temperature affect the overall pressure level. Review these alongside the high-point pressure and equipment ratings; use the expansion-tank guide for the separate volume and pressure checks.

A larger pump is not an automatic cure for an inlet problem. A higher flow may increase suction-side losses while changing the required NPSH. Review the strainer condition, valve positions, inlet routing and actual operating point before replacing equipment. Do not throttle the suction line as a cavitation remedy.

Raising fill pressure also changes the pressure seen elsewhere. Any proposed adjustment must remain within the approved expansion, relief and component-pressure design. Do not change a relief setting or open a hot pressurized circuit to test an idea. Instrument installation and service belong under the equipment’s isolation and safety procedures.

7. Build a reviewable operating-case schedule

A useful schedule ties every NPSHA result to a real operating case. Record the highest fluid temperature that can coincide with the lowest inlet pressure, the highest permitted flow and the relevant speed. Include allowed parallel operation and control changes. Do not combine unrelated extremes without saying whether that combination can occur.

For each case, preserve the suction tap location, elevation reference, gauge or absolute basis, instrument range and calibration information. Record the property source and fluid concentration. If pressure is calculated from a remote point, show every intervening loss once and identify which restrictions represent clean or service conditions.

Then attach the manufacturer’s selection sheet with the applicable NPSHR and margin requirement. The final review should also address the pump’s allowable operating region, inlet geometry, component pressure ratings and control sequence. Passing the NPSH arithmetic does not answer those separate selection questions.

  • Compare like units: metres of the actual liquid are not automatically metres of reference water or a pressure in kPa.
  • Use the pump’s required datum, particularly when a pressure instrument is above or below the inlet.
  • Investigate uncertainty when the result is close to the selection target; rounding cannot create a margin.
  • Retain both expected and commissioning operating conditions so future changes can be traced.

8. Download the example and keep the calculation connected

Download the worked NPSH pressure budget and sensitivity CSV to audit the example inputs and unrounded results. It includes the assumed selection target separately from the physical system calculation, so the two are not confused.

Use the pump inlet review checklist CSV to collect operating cases, pressure references, fluid properties and supplier evidence. It is a blank review aid, not an equipment selector. Replace the example assumptions with the project’s supported inputs before drawing a conclusion.

MEPFlow brings hydronic layouts and sizing into a browser-based design workflow. Keep the circuit flow and pressure-loss calculation connected to the drawing, then carry the selected operating cases into the pump supplier’s review. The useful handoff is a traceable set of inputs, a defined pressure datum and an equipment selection that answers both circulation and inlet-condition questions.

Frequently asked questions

Is NPSH the same as pump head?

No. Duty head is the energy added across the pump to circulate flow. Available NPSH describes total absolute suction head above the liquid’s vapor-pressure head at the specified pump datum. Check both.

Can a closed hydronic system cavitate?

Yes. Local inlet pressure can become inadequate for the fluid temperature and pump requirement. Pressurization, tank connection, inlet losses and operating flow must be assessed together.

Should I use gauge or absolute pressure?

Vapor pressure is absolute. Convert a gauge reading by adding the local atmospheric pressure, and preserve the pressure tap and elevation datum. Do not add atmosphere again to an already absolute measurement.

Is NPSHR always the 3% head-drop value?

No. NPSH3 identifies the 3% test condition. The manufacturer’s published NPSHR can be higher. Confirm the curve basis and application margin instead of treating the labels as interchangeable.

Can I subtract the strainer loss from a measured inlet reading?

Not if the running pressure reading is already at the pump inlet downstream of that strainer: its effect is included. If the reading comes from upstream, translate the total head to the inlet and include intervening losses once.

Does higher water temperature always reduce actual NPSHA?

At fixed inlet pressure and flow, rising vapor pressure usually reduces available NPSH over typical hydronic temperatures. In a real closed system, pressure also changes with thermal conditions, so evaluate coincident conditions rather than temperature alone.

Continue the engineering workflow

Connect the hydronic duty to the supplier review

Use MEPFlow for hydronic layouts and circuit sizing. Check the separate inlet-pressure budget with the worksheets below and the pump supplier’s selection data.

Start free trial

Primary references

Sources and further reading for the methods discussed in this guide.